Thread Rating:
  • 1 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Generated Windows USB stick does stuck on boot screen
#11
(11-24-2015, 02:10 AM)fuzzi Wrote: I have same problems with win 7 home prem. Fresh setup system.
Fresh installed and updated win2usb. 64 GB USB stick.

All 3 methods - using iso, dvd, local system - produce a stick with correct data written on it, but when it comes to boot from the stick it ends up with a blue screen (0x00000007b) - always.
I tried it with an ide-hdd installed or without - same results.

The notebook I'm using is prepared to boot from usb, I can boot any linux installation from usb without problems.

Any ideas what I could try?
thx

Windows 7 does not have built-in USB 3.0 support, so Windows 7 to go drive must be to boot from a USB 2.0 port, please insert your usb drive to a USB 2.0 port and try again.

BTW, we recommend using Windows 10/8.1/8 to create portable Windows, because Windows 10/8.1/8  To Go have better compatibility.
Reply
#12
Hello,
How can I change the size of the partition ?
I have 16GB and I need the windows to be on 10GB only, is that possible?
Reply
#13
(12-04-2015, 05:46 PM)USBlover Wrote: Hello,
How can I change the size of the partition ?
I have 16GB and I need the windows to be on 10GB only, is that possible?

Why did you do that? After you create the Windows To Go drive, maybe you can use a third-party partitioning tool to resize the partition.
Reply
#14
(12-04-2015, 10:15 PM)admin Wrote:
(12-04-2015, 05:46 PM)USBlover Wrote: Hello,
How can I change the size of the partition ?
I have 16GB and I need the windows to be on 10GB only, is that possible?

Why did you do that? After you create the Windows To Go drive, maybe you can use a third-party partitioning tool to resize the partition.

Can I choose the size of the partition, if so, how?
Reply
#15
hello usblover i am also having same problem how can I change the size of the partition i have 64 GB and i am using windows 7.????????????????
Reply
#16
(12-05-2015, 03:47 AM)USBlover Wrote:
(12-04-2015, 10:15 PM)admin Wrote:
(12-04-2015, 05:46 PM)USBlover Wrote: Hello,
How can I change the size of the partition ?
I have 16GB and I need the windows to be on 10GB only, is that possible?

Why did you do that? After you create the Windows To Go drive, maybe you can use a third-party partitioning tool to resize the partition.

Can I choose the size of the partition, if so, how?

Sorry, WinToUSB doesn't support it. Please try third-party partitioning tool (acronis disk director suite, minitool partition wizard, et c) to resize the partition after creating the W2G drive.
Reply
#17
Well, learn more sent me here.

I tried WinToUSB to clone my windows system to a 32gb usb.

It worked the first time. foolishly I tried it again, and it wiped the usb then failed

9:31a install wintousb
http://www.easyuefi.com/wintousb/faq/en_...ToUSB.html
update to new versio
http://www.easyuefi.com/wintousb/faq/en_...ToUSB.html
wintousb clone
Microsoft Windows 7 Starter (x86)
6.1.760 Build 7600
C:, NTFS, Used: 19.67 GB, Capacity: 80.00 GB
Legacy BIOS
9:38 next
learn more
http://www.easyuefi.com/forums/showthrea...t=smoothly
9:40a formating
9:41a system and boot
http://www.easyuefi.com/wintousb/faq/en_...tions.html
9:42a winpe build
9:44a reboot required
9:52a and failed
error 0x0005000200f70000

win wanted to format the usb to see it

diskpart said the volume was fs raw.

any help?
Reply
#18
Well, learn more sent me here.

I tried WinToUSB to clone my windows system to a 32gb usb.

It worked the first time. foolishly I tried it again, and it wiped the usb then failed

9:31a install wintousb
http://www.easyuefi.com/wintousb/faq/en_...ToUSB.html
update to new versio
http://www.easyuefi.com/wintousb/faq/en_...ToUSB.html
wintousb clone
Microsoft Windows 7 Starter (x86)
6.1.760 Build 7600
C:, NTFS, Used: 19.67 GB, Capacity: 80.00 GB
Legacy BIOS
9:38 next
learn more
http://www.easyuefi.com/forums/showthrea...t=smoothly
9:40a formating
9:41a system and boot
http://www.easyuefi.com/wintousb/faq/en_...tions.html
9:42a winpe build
9:44a reboot required
9:52a and failed
error 0x0005000200f70000

win wanted to format the usb to see it

diskpart said the volume was fs raw.

any help?
Reply
#19
Do you mean to say the USB drive is damaged?
Reply
#20
No, I could use diskpart to reformat the USB, but it sure was not bootable any more.

DISKPART> list volu

Volume ### Ltr Label Fs Type Size Status Info
---------- --- ----------- ----- ---------- ------- --------- --------
Volume 0 C NTFS Partition 79 GB Healthy System
Volume 1 D NTFS Partition 59 GB Healthy
Volume 2 E RAW Removable 29 GB Healthy

DISKPART> clean
diskpart
list disk
select disk 1
clean
create partition primary
select partition 1
active
format fs=ntfs quick
exit

WinToUSB left my USB flash drive raw.

So what is
error 0x0005000200f70000
Reply


Forum Jump:


Users browsing this thread: 4 Guest(s)