Hello:
I am trying to clone a 500GB HDD (internal) because of intermittent problems to my other 500GB HDD (internal) using WintoHDD. The clone process goes through without a hitch but when I restart with the cloned drive after removing the main drive, I get the following error message (as the subject of this post) - 0xc000000f the boot selection failed because a required device is inaccessible.
I have an HP Laptop dv7. Put the cloned drive into the 1st bay as is required for the boot to work.
I have tried cloning twice. The first time I did it with the System and boot partition in one and the second time the boot partition and system partition (1GB allocated) in two separate partition. The current set up is shown in the attached HDDPartition image.
Would appreciate if you could help in resolving the above issue.
Regards,
Dave

Attached Files

Thumbnail(s)
   

I have a laptop HDD but how can convert to a portable drive?

Hello,
I successfully installed windows 10 Pro on a 128 Gb Sandisk USB thumb drive.
It works flawlessly, however every now and the I get a message in Windows saying that I do not have enough free space in the drive where the VHDX file is.
How is it possible?
Does Windows 10 Pro really take 128 Gb of space?

Please help.
Thank you!
iR

Hello,
I just bought:
WintoUSB
Bitlock Anywhere.

I was able to successfully use WintoUSB ad install Windows 10 Pro on a Sandisk Extreme Pro USB Thumb Drive.
I would like to install Bitlock and Encrypt the Windows on the USB.
When I start Bitlock Anywhere it shows the hard disk (C: My computer) and 2 removable drives D: (this contains Boot, EFI, Bootmgr) and E: (WintoUSB which contains a file Win2USB.VHDX).

Which one should I select?

Thanks
iR

Hello i wanna ask about installing windows from created USB with WinToHDD
I went trought all steps and at screen where Disk partitions its so confusing here what i did first time but i think i messed something i posted a photo what i did first time when i installed windows 10 from it i think i tick something wrong on that photo i did all that but now second time i miss some partition FAT or so dont remember?

Can someone help me with it, what did i tick wrong if so how to fix that and what is correct system and boot partition to tick in my case ?

Thanx.  

Attached Files

Thumbnail(s)
   

I’m using a Macbook Pro 2017 and worked with WTG drivers for months. Recently i bought NVIDIA RTX graphic cards but my older version 1703 doesn’t work with RTX. I have to upgrade my Windows into 1809 so I chose WinToUSB to do that. I erased and formatted my drive and installed WTG correctly, but after I successfully booted the first time into WTG and installed the Boot Camp drivers and restarted, the WTG cannot be booted anymore. I erased again and clean installed again and things are the same. I want to know what’s the problem here, thank you!

The drive I am using is a Sandisk SSD with a SATA USB C case. I also tried to connect to the SATA port of my eGPU case and use the Thunderbolt 3 as I used to do, but didn’t work as well.

The latest one is unable to make Multi-Installation USB on Windows-10 64bit system.

It always fails after reaching till 95% with a very common error code and status (which unfortunately elaborates NOTHING): Failed to run system API.

Worth to be mentioned, the Firewall/Antivirus/Administration Privilege all have been enabled/disabled/tested gradually, but the result remained the same as it is. Same case with different Device/Computers but with same Windows-10.

But with Windows-8/8.1 the situation is totally different. Everything works fine with no issue at all. Same system I've re-installed Windows-8.1 Enterprise replacing of Windows-10 Enterprise, and it worked like charm!!!

Please fix it guys, no log to be attached for this, as it seems to be a very common issues from very beginning. And please make some changes in your error logs, which just prompts but explains nothing!

Another issue was found while making Multi-Installation USB HDD. It never shows that Format Checkbox, due to that the NTFS Drive just gets the data copied but doesn't get linked with UEFI Partition. Same had been tested with both Windows-8.1 & Windows-10 as well.

Again, no Log file is required to upload to describe these kinda issues, as these seems to be very common bugs which could be fixed easily enough.

Cheers.

Hello,
I have wintousb installed as vhdx.
when native booting the system starts without problems, but always comes with the Windows performance optimization, since no paging file can be created. What have I done wrong. Please help.

The changes made so that 1809 works seem to be reversed when sfc /scannow is run. I was attempting to fix an issue where Legacy booting worked but EFI would hang on loading everytime, recreated the boot partition with bcdboot, didn't work, tried sfc /scannow and now the system blue screens every time I boot legacy or EFI.

Just something for others to take note of.

Hello. I hope I'm posting in the proper thread.

It would appear after 4 days of trying to determine the issue I'm experiencing that your product will not work with a PNY Turbo 256GB USB 3.0 Flash Drive.

I have an Asus ROG G75VW it only has USB 3.0 ports. I was attempting to install Windows 8.1 from a verified working ISO.
My PNY Turbo 256GB USB 3.0 Flash Drive keeps throwing a BSOD USB 3.0 BUG error code.

I used a micro SD card after my 4th day of process of elimination and it works fine!

So it's not user error. Can you please tell of a remedy for the issue other than to insert a USB 2.0 stick or port?

If not I'll look elsewhere for a product that can suit my needs.

Thanks for your time.